跳转到内容

购物车

文章: Cocktail Stencils for Bars: Sizing a Logo for the Glass

bridges

Cocktail Stencils for Bars: Sizing a Logo for the Glass

A cocktail stencil is a flat sheet with your logo cut through it. It rests across the rim of the glass, the bartender dusts cocoa, cinnamon or another fine powder over it, and the logo lands on the foam. Ours are 190 mm wide overall including the handles, with a 110 mm open area in the middle and a logo of up to 100 mm. The open area is the number that matters: measure the inside of the rim on the glass you serve in, and size the logo to sit inside it.

Why the cocktail size is larger than the coffee size

A coffee stencil is 130 mm overall with an 80 mm open area and a logo of up to 70 mm, sized for a standard cup. Cocktail glasses vary far more. A coupe, a martini glass and a wide sour glass all present a different surface, and the foam on a shaken drink sits at a different height from the crema on a flat white. The larger cocktail sheet spans the wider rims and leaves room for a logo that still reads from across the bar. If the glass you use is narrower than the logo, the edges of the design fall outside the foam and onto the glass, so size to the glass, not the menu.

Bridges: what changes when a logo becomes a stencil

Any closed shape in a logo has a middle that is not attached to anything. The counter of an O, the centre of an A or R, a ring around a crest: cut those as drawn and the middle drops out, leaving a solid blob where the shape should be. A stencil handles this with bridges, small ties of sheet that hold the island in place. In powder they read as thin gaps in the line.

On a coffee or cocktail stencil, the bridges are part of the look, so they need to be placed with care. We put them where the eye expects a break, such as the top and bottom of an O, or where a stroke already thins. A logo with a lot of enclosed detail may need simplifying so the bridges do not chop it into pieces. We send a proof with the bridges drawn in before anything is cut, so you can see exactly how the logo will land on the drink.

Fine detail at 100 mm

Powder is a coarse medium. It does not hold a hairline, and it does not hold very small text. A logo that reads well on a business card can turn to noise when it is dusted at 100 mm across. Thin strokes fill in or break up, and small lettering under a wordmark is usually the first thing to go. Not every logo or font suits a cocktail stencil, and we will say so when we send the complimentary design file, adjusting the artwork so it reads at size. The usual fixes are thicker strokes, fewer elements and dropping secondary text such as a tagline.

Material: acrylic or Mylar

We cut cocktail stencils in three food-safe materials:

  • Acrylic, 3 mm. Rigid, so it rests flat across the rim instead of sagging toward the foam, which keeps the dusted edge sharp and the result the same from glass to glass. It also comes out of the wash flat. This is our recommendation for daily service.
  • Commercial Mylar, 0.35 mm (14mil). Lighter and lower cost, and still lies flat across a standard rim.
  • Mylar, 0.19 mm (7.5mil). The most flexible. It is the one to use when the stencil needs to sit down toward a domed surface or follow a curve, and it holds the finest detail.

Both Mylar thicknesses are the same price.

In service

A stencil that is in the wash is not on the bar. Busy venues order duplicates so one can be cleaned while the other is in use. Care is simple: wash in warm soapy water before first use and after each service, then dry flat. Drying flat matters more for the Mylar options, which are thin enough to take a set if they are left curled.

Keep the stencil close to the surface when you dust. The further the sheet sits above the foam, the more the powder spreads under the edges and softens the logo. A fine sieve or shaker gives a more even coat than pinching powder over the sheet.

How ordering works

You can type your wording and pick a stencil font on the product page and see it at true proportions, or upload your logo. We prepare the design and cut file, and send a digital proof within 1 to 2 business days for you to approve. Once you approve it, we cut and pack the stencil and dispatch it within 2 business days, tracked. Shipping within Australia is free on orders over A$99. Custom coffee and cocktail stencils start from A$21 inc GST on the product page. For a larger size or a different colour material, contact us before ordering.

Order a custom coffee or cocktail stencil, see the pre-made range, or read our guide to coffee stencils for cafés and events and why stencils need bridges.

发表评论

此站点受 hCaptcha 保护,并且 hCaptcha 隐私政策和服务条款适用。

所有评论在发布前都会经过审核。

Read more

Mylar

Overspray Margin: How Much Sheet to Leave Around a Stencil

The overspray margin is the border of sheet that catches spray around a stencil design. Here is how to size it, and how it interacts with bridges and material gauge.

阅读更多